CronoLine IL-E (High Flow, VSD)

In-Line Design

Pumping of heating water (acc. to VDI 2035), cold water and water/glycol mixtures without abrasive substances in heating, cold water and cooling systems.

Electronically controlled glanded single pump in in-line design with flange connection and automatic power adjustment

CronoLine IL-E 

Technical Data:

  • Permissible temperature range -20 °C to +140 °C
  • Mains connection
    • 3~440 V ±10 %, 50/60 Hz
    • 3~400 V ±10 %, 50/60 Hz
    • 3~380 V -5 % +10 %, 50/60 Hz
  • Protection class IP 55
  • Nominal diameter DN 40 to DN 200
  • Max. operating pressure 16 bar up to +120 °C, 13 bar up to +140 °C

  • Energy savings due to integrated electronic power adjustment.
  • Optional interfaces for bus communication using plug-in IF-Modules.
  • Simple operation with Green Button Technology and display.
  • Integrated dual pump management.
  • Integrated full motor protection (PTC thermistor sensor) with trip electronics.

Pumping of heating water (acc. to VDI 2035), cold water and water/glycol mixtures without abrasive substances in heating, cold water and cooling systems.

  • Irrigation
  • Building Services
  • General Industry
  • Power Station

Electronically controlled glanded single pump in in-line design with flange connection and automatic power adjustment.

Single-stage, low-pressure centrifugal pump in in-line design with:

  • Mechanical seal
  • Flange connection
  • Lantern
  • Coupling
  • Drive with integrated electronic speed control


Materials:

  • Pump housing and lantern: EN-GJL-250
  • Impeller
  • Standard version: EN-GJL-200
  • Special version: Bronze CuSn 10
  • Shaft: 1.4122
  • Mechanical seal: AQEGG; other mechanical seals on request

Operating Modes:

  • Δp-c for constant differential pressure
  • Δp-v for variable differential pressure
  • PID control
  • Constant speed (n=constant)

Manual Operation Level:

  • Green button and display

Manual Functions:

  • Differential pressure setpoint setting
  • Setting the speed (manual control mode)
  • Setting the operating mode
  • Setting the pump ON/OFF
  • Configuration of all operating parameters
  • Fault acknowledgement

External Control Functions:

  • "Overriding Off" control input
  • “External pump cycling” control input (effective only in dual pump operation)
  • Analogue input 0 – 10 V, 0 – 20 mA for constant speed (DDC) and remote setpoint adjustment
  • Analogue input 2 – 10 V, 4 – 20 mA for constant speed (DDC) and remote setpoint adjustment
  • Analogue input 0 – 10 V for actual value signal from pressure sensor
  • Analogue input 2 – 10 V, 0 – 20 mA, 4 – 20 mA for actual value signal from pressure sensor

Signal and Display Functions:

  • Collective fault signal SSM
  • Collective run signal SBM

Data Exchange:

  • Infrared interface for wireless data exchange with IR-Monitor/IR-Stick
  • Plug-in position for Wilo IF-Modules (Modbus, BACnet, CAN, PLR, LON) for connection to building automation

Safety Functions:

  • Full motor protection with integrated trip electronics
  • Access disable

Dual Pump Management (Twin-head pump or 2 x single pumps):

  • Main/standby operation (automatic fault-actuated switchover)
  • Pump cycling main/standby operation after 24 hours
  • Parallel operation
  • Parallel operation (efficiency-optimised peak-load activation and deactivation)

Technical Data

Wilo Pump Range

Wilo Pump Range

Wilo Pump Range

Wilo Pump Range

Wilo Pump Range

Enquire Now

At Temperzone, we like to ensure that you are provided with the best information and support. Should you have an enquiry, please make contact. We're always here to help.